Woven Wire Mesh Partitions
 

WOVEN WIRE MESH PARTITIONS

 

Wire mesh partitions are available in a variety of mesh patterns, channel sizes and spacings and include standard and heavy duty use and low and high type wire mesh partitions. All wire mesh partitions are designed to meet any building code.

Diamond Mesh: The geometry of triangulation. It's unsurpassed strength makes it a superior product compared to other mesh shapes.

 

STANDARD DUTY LOW TYPE WIRE MESH PARTITION

Panels are made in any width up to 5-0 wide.
Single panel height recommended to 12-0.
Mesh: 10ga. (.135) steel wire triple crimped and woven into a 1 1/2 diamond mesh.
Vertical Frame: 1 1/4" x 5/8" x .080 "C" type steel channel
Horizontal Frame: 1" x 1/2" x 1/8" steel channel
Horizontal Stiffeners: Two 1" x 3/8" x 1/8" steel channels or
Two 3/4" x 3/8" x 1/8" steel channels toe riveted or bolted through mesh or
One 1" x 1/2" x 1/8" woven in channel
Panel frames mortised and tenoned at corners.
Hinged Door Frames:
(4 sides)
1 1/4" x 1/2" x 1/8" steel channel or
1 1/4" x 5/8" x .080 "C" type steel channel with 1 1/4 x 1/8 steel flat bar capping
Sliding Gate Frames:
(4 sides)
1 1/2" x 3/4" x 1/8" steel channel with 1 1/2" x 1/8" steel flat bar capping
Locks: Mortise type cylinder lock with recessed turn knob inside and mortise cylinder outside.
Corner Posts: 1 1/4" x 1 1/4" x 1/8" steel angle or
1 1/4" x 1 1/4" x 1/8" square tube
Top Capping: 2 1/4" x 1" steel channel with 1/4" diameter bolt and nut min. 28" o.c.
Fasteners: 1/4" diameter bolt and nut vertically min. 12" o.c.
LOW TYPE WIRE MESH PARTITION

STANDARD DUTY HIGH TYPE WIRE MESH PARTITION

For partitions over 12'-0" high, vertical posts must be added for increased rigidity. This special reinforcement when installed between panels gives maximum strength for greater heights. This reinforcement is also recommended for lower height partitions where extra strength is required.

Vertical Stiffeners: Partition Height Material
up to 16'
16' to 24'
over 24'
5/16" x 2 1/2" flat
5/16" x 3" flat
3" channel with welded base plate
HIGH TYPE WIRE MESH PARTITION

HEAVY DUTY LOW AND HIGH TYPE WIRE MESH PARTITION

Mesh: 6ga. (.192) steel wire triple crimped and woven into a 2 diamond mesh.
Vertical Frame: 1 1/2" x 3/4" x 1/8" steel channel
Horizontal Frame: 1 1/2" x 3/4" x 1/8" steel channel
Horizontal Stiffeners: Two 1" x 1/2" x 1/8" channels
Panel frames mortised and tenoned at corners.
Hinged Door Frames:
(4 sides)
1 1/2" x 3/4" x 1/8" steel channel with 1 1/2" x 1/8" flat bar capping
Sliding Gate Frames:
(4 sides)
1 1/2" x 3/4" x 1/8" steel channel with 1 1/2" x 1/8" flat bar capping
Locks: Mortise type cylinder lock with recessed turn knob inside and mortise cylinder outside.
Corner Posts: 1 1/2" x 1 1/2" x 1/8" steel angle or
1 1/2" x 1 1/2" x 1/8" square tube
Top Capping: 3" x 1" steel channel with 3/8" diameter bolt and nut min. 28" o.c.
Fasteners: 3/8" diameter bolt and nut vertically min. 12" o.c.
Vertical Stiffeners: Partition Height Material
up to 16'
16' to 24'
over 24'
5/16" x 2 1/2" flat
5/16" x 3" flat
3" channel with welded base plate
Finish Options: Prime Painted
Hot-Dip Galvanized
One Finish Coat
Powder Coated
Other Available Options
Packaging: When material is shipped, paint finish may be marred.Field touch-up is normally required. Touch-up paint shall be provided.When special finishes are required, special packaging may be necessary.
HIGH TYPE WIRE MESH PARTITION
Technical Specifications  

Installation: Wire partitions are designed that they may be erected by inexperienced labor. Shop Drawings are sent with all jobs so that your erector will understand how parts are assembled. Field bracing of partitions may be required, depending on the individual project and customer preferences. Bracing materials will be furnished only when the type and quantity are specified and requested. (Bracing is usually provided by the erector). All bolts and nuts that are required for assembly are provided. However, bolts, screws, floor and wall anchors required for attachment to building structure are not included, unless specified and requested.

Ordering: When ordering it is best to send a rough sketch, so that we may fabricate with the correct locations of doors and or sliding gates. Indicate the hinge side, swing direction and key side of all doors and sliding gates. Be sure to state the height and type of floor and wall conditions to which the partition are anchored. If there are pipes, ducts, beams, or other structural obstructions around which the partition must fit, please dimension these locations and their elevations (AFF above finished floor).

Click here to request a quote.

 

 
 

corel dvd moviefactory 6

corel dvd moviefactory 6 downloads

key office 2010

office 2010 key

free corel photoshop download

free corel photoshop download keygen

winrar password cracker serial

wirar password cracker

download photo shop free

photo shop serial

photo shop key

photo shop key

serial corel draw 11

serial corel draw 11 serials

adobe free

adobe free

free corel downloads

free corel downloads cracked

windows key

windows key

cs5 serialz

cs5 serialz free

free winrar download for xp

download winrar for xp for free

office 2010 free

office 2010 key

photoshop key

photoshop key

windows 7 key

windows 7 key

office 2010 professional key

office 2010 key

serial winzip 11

serial winzip 11 key

windows 7 free

windows 7 crack

winrar 3 download

winrar 3 download freedownload